Synthesis and characterization of an interpenetrating polymer network composed of poly(methacrylic acid) and poly(vinyl alcohol)

Temperature and pH‐responsive interpenetrating polymer network (IPN) hydrogels, constructed with poly(methacrylic acid) (PMAA) and poly(vinyl alcohol) (PVA), by a sequential IPN method, were studied. The characterization of IPN hydrogels was investigated by Fourier‐transform infrared spectroscopy, differential scanning calorimetry (DSC) and swelling under various conditions. The IPN hydrogels exhibited relatively high swelling ratios, in the range 230–380 %, at 25 °C. The swelling ratios of the PMAA/PVA IPN hydrogels were pH and temperature dependent. DSC was used for the quantitative determination of the amounts of freezing and non‐freezing water. The amount of free water increased with increasing PMAA content in the IPN hydrogels. Copyright © 2004 Society of Chemical Industry     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Broadly wavelength-tunable external cavity lasers with extremely low power variation over tuning range

Tunable external-cavity lasers with low power variation over a broad tuning range are demonstrated using asymmetric multiple quantum-wells with a wide and flat gain. For a 2.8-/spl mu/m-wide ridge waveguide laser of cavity length 380 /spl mu/m, when used in a grating external cavity and with an antireflection coating on one facet of laser diode chip, the power variation of less than -1 dB is obtained over a range of 80 nm. This extremely low power variation is a direct result of the spectrally flat gain.     

Dielectric reliability of stacked Al2O3–HfO2 MIS capacitors with cylinder type for improving DRAM data retention characteristics

Dielectric reliability in Al₂O₃(2–3.1nm)–HfO₂(3nm) stack capacitor with Metal–Insulator–Si(MIS) structure is investigated in this paper. We propose an optimized capacitor process through the Time–Dependent Dielectric Breakdown (TDDB) data under various process conditions. Furthermore, due to asymmetric current at both negative and positive voltage stress polarities, we show different lifetime extrapolation by a fluence–driven model. As a result, the maximum allowed operating voltage is projected to be 1.7V (failure rate 10ppm during 10year @ 85°C) for Data “0” retention lifetime.     

A simple mathematical analysis on the effect of sand in Cr(VI) reduction using zero valent iron

A simple mathematical model was proposed to analyze the enhancement of Cr(VI) reduction when sand materials are added to the zero valent iron (ZVI). Natural decay of Cr(VI) in a control experiment was analyzed by using a zero-order decay reaction. Adsorption kinetics of Cr(VI) to sand was modeled as a first-order reversible process, and the reduction rate by ZVI was treated as a first-order reaction. Natural decay of Cr(VI) was also included in other experiments, i.e., the adsorption to sand, the reduction by ZVI, and both adsorption and reduction when sand and ZVI are present together. The model parameters were estimated by fitting the solution of each model to the corresponding experimental data. To observe the effect of sand addition to ZVI, both adsorption and reduction rate models were considered simultaneously including the natural decay. The solution of the combined model was fitted to the experimental data to determine the first-order adsorption and reduction rate constants when sand as well as ZVI is present. The first-order reduction rate constant in the presence of sand was about 35 times higher than that with ZVI only.     

Production and structural features of a water-soluble polysaccharide from a mutant strain of Agrobacterium sp.

We have developed a mutant strain derived from Agrobacterium sp. ATCC 31750, which produces a water-soluble polysaccharide having potential utility to the food, feed, pharmaceutical and cosmetic industries. A high concentration of product (15 g/L) is obtained by 48 h cultivation of the mutant strain under optimized fermentation conditions. The water-soluble polysaccharide obtained from cultures of the mutant strain beta82 has Glc:Man:Gal in approximate molar ratios of 5.8:6.7:1.0. The molecular weight of the polysaccharide was determined to be approximately 1000 kDa by HPSEC analysis. Linkage analysis contained 3-Glcp, 3-Manp, terminal Glcp and terminal Manp, as well as a small proportion of 3- and 3,4-Galp, and 4,6-Manp residues. Based on analyses using FT-IR and ¹³C NMR spectrometers, most glycosidic bonds joining these sugar residues are of the α-type, and acetyl groups are apparently attached to the polymer chain at random.     

Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.     

Revisiting the need for formal education in visualization.

Defining visualization education is still a work in progress. Visualization education is not just a subject within computer science. Computer scientists are not always the appropriate choice to teach visualization courses on their own. Visualization is not just mastering a set of concepts but acquiring skills. Student should learn by doing, either using one tool or a variety of tools, depending on the course's focus.